Previewing GeForce RTX 2080 Ti

Turing and NVIDIA’s focus on hybrid rendering aside, let’s take a look at the individual GeForce RTX cards.

Before getting too far here, it’s important to point out that NVIDIA has offered little in the way of information on the cards’ performance besides their formal specifications. Essentially the entirety of the NVIDIA Gamescom presentation – and even most of the SIGGRAPH presentation – was focused on ray tracing/hybrid rendering and the Turing architecture’s unique hardware capabilities to support those features. As a result we don’t have a good frame of reference for how these specifications will translate into real-world performance. Which is also why we’re disappointed that NVIDIA has already started pre-orders, as it pushes consumers into blindly buying cards.

At any rate, with NVIDIA having changed the SM for Turing as much as they have versus Pascal, I don’t believe FLOPS alone is an accurate proxy for performance in current games. It’s almost certain that NVIDIA has been able to improve their SM efficiency, especially judging from what we’ve seen thus far with the Titan V. So in that respect this launch is similar to the Maxwell launch in that the raw specifications can be deceiving, and that it’s possible to lose FLOPS and still gain performance.

In any case, at the top of the GeForce RTX 20 series stack will be the GeForce RTX 2080 Ti. A major departure from the GeForce 700/900/10 series, NVIDIA is not retaining the Ti card as a mid-generation kicker. Instead they’re launching with it right away. This means that the high-end of the RTX family is now a 3 card stack from the start, instead of a 2 card stack as has previously been the case.

NVIDIA has not commented on this change in particular, and this is one of those things that I expect we’ll know more about once we reach the actual hardware launch. But there’s good reason to suspect that since NVIDIA is using the relatively mature TSMC 12nm “FFN” process – itself an optimized version of 16nm – that yields are in a better place than usual at this time. Normally NVIDIA would be using a more bleeding-edge process, where it would make sense to hold back the largest chip another year or so to let yields improve.

NVIDIA GeForce x80 Ti Specification Comparison
  RTX 2080 Ti
Founder's Edition
RTX 2080 Ti GTX 1080 Ti GTX 980 Ti
CUDA Cores 4352 4352 3584 2816
ROPs 88? 88? 88 96
Core Clock 1350MHz 1350MHz 1481MHz 1000MHz
Boost Clock 1635MHz 1545MHz 1582MHz 1075MHz
Memory Clock 14Gbps GDDR6 14Gbps GDDR6 11Gbps GDDR5X 7Gbps GDDR5
Memory Bus Width 352-bit 352-bit 352-bit 384-bit
Single Precision Perf. 14.2 TFLOPs 13.4 TFLOPs 11.3 TFLOPs 6.1 TFLOPs
"RTX-OPS" 78T 78T N/A N/A
TDP 260W 250W 250W 250W
GPU Big Turing Big Turing GP102 GM200
Architecture Turing Turing Pascal Maxwell
Manufacturing Process TSMC 12nm "FFN" TSMC 12nm "FFN" TSMC 16nm TSMC 28nm
Launch Date 09/20/2018 09/20/2018 03/10/2017 06/01/2015
Launch Price $1199 $999 MSRP: $699
Founders: $699

The king of NVIDIA’s new product stack, the GeForce RTX 2080 Ti is without a doubt an interesting card. And if we’re being honest, it’s not a card I was expecting. Based on these specifications, it’s clearly built around a cut-down version of NVIDIA’s “Big Turing” GPU, which the company just unveiled last week at SIGGRAPH. And like the name suggests, Big Turing is big: 18.6B transistors, measuring 754mm2 in die size. This is closer in size to GV100 (Volta/Titan V) than it is any past x80 Ti card, so I am surprised that, even as a cut-down chip, NVIDIA can economically offer it for sale. None the less here we are, with Big Turing coming to consumer cards.

Even though it’s a cut-down part, RTX 2080 Ti is still a beast, with 4352 Turing CUDA cores and what I estimate to be 544 tensor cores. Like its Quadro counterpart, this card is rated for 10 GigaRays/second, and for traditional compute we’re looking at 13.4 TFLOPS based on these specifications. Note that this is only 19% higher than GTX 1080 Ti, which is all the more reason why I want to learn more about Turing’s architectural changes before predicting what this means for performance in current-generation rasterization games.

Clockspeeds have actually dropped from generation to generation here. Whereas the GTX 1080 Ti started at 1.48GHz and had an official boost clock rating of 1.58GHz (and in practice boosting higher still), RTX 2080 Ti starts at 1.35GHz and boosts to 1.55GHz, while we don’t know anything about the practical boost limits. So assuming NVIDIA is being as equally conservative as the last generation, then this means the average clockspeeds have dropped slightly. Which in turn means that whatever performance gains we see from GTX 2080 Ti are going to ride entirely on the increased CUDA core count and any architectural efficiency improvements.

Meanwhile the ROP count is unknown, but as it needs to match the memory bus width, we’re almost certainly looking at 88 ROPs. Even more so than the core compute architecture, I’m curious as to whether there are any architectural improvements here. Otherwise because the ROP count is identical, then the maximum pixel throughput (on paper) is actually ever so slightly lower than it was on GTX 1080 Ti.

Speaking of the memory bus, this is another area that is seeing a significant improvement. NVIDIA has moved from GDDR5X to GDDR6, so memory clockspeeds have increased accordingly, from 11Gbps to 14Gbps, a 27% increase. And since the memory bus width itself remains identical at 352-bits wide, this means the final memory bandwidth increase is also 27%. Memory bandwidth has long been the Achilles heel of GPUs, so even if NVIDIA’s theoretical ROP throughput has not changed this generation, the fact of the matter is that having more memory bandwidth is going to remove bottlenecks and improve performance throughout the rendering pipeline, from the texture units and CUDA cores straight out to the ROPs. Of course, the tensor cores and RT cores are going to be prolific bandwidth consumers as well, so in workloads where they’re in play, NVIDIA is once again going to have to do more with (relatively) less.

Past this, things start diverging a bit. NVIDIA is once again offering their reference-grade Founders Edition cards, and unlike with the GeForce 10 series, the 20 series FE cards have slightly different specifications than their base specification compatriots. Specifically, NVIDIA has cranked up the clockspeed and the resulting TDP a bit, giving the 2080 Ti FE an on-paper 6% performance advantage, and also a 10W higher TDP. For the standard cards then, the TDP is the x80 Ti-traditional 250W, while the FE card moves to 260W.

Meanwhile, starting with the GeForce 20 series cards, NVIDIA is rolling out a new design to their reference/Founders Edition cards, the first such redesign since the original GeForce GTX Titan back in 2013. Up until now NVIDIA has focused on a conservative but highly effective blower design, pairing the best blower in the industry with a metal grey & black metal shroud. The end result is that these reference/FE cards could be dropped in virtually any system and work, thanks to the self-exhausting nature of blowers.

However for the GeForce 20 series, NVIDIA has blown off the blower, and instead opted to design their cards around the industry’s other favorite cooler design: the dual-fan open air cooler. Combined with NVIDIA’s metallic aesthetics, which they have retained, and the resulting product pretty much looks exactly like you’d expect a high-end open air cooled NVIDIA card to look like: two fans buried inside a meticulous metal shroud. And while we’ll see where performance stands once we review the card, it’s clear that NVIDIA is at the very least aiming to lead the pack in industrial design once again.

The switch to an open air cooler has three particular ramifications versus NVIDIA’s traditional blower, which for regular AnandTech readers you’ll know we’ve discussed before.

  1. Cooling capacity goes up
  2. Noise levels go down
  3. A card can no longer guarantee that it can cool itself

In an open air design, hot air is circulated back into the chassis via the fans, as the shroud is not fully closed and the design doesn’t force hot air out of the back of the case. Essentially in an open air design a card will push the hottest air away from itself, but it’s up to the chassis to actually get rid of that hot air. Which a well-designed case will do, but not without first circulating it through the CPU cooler, which is typically located above the GPU.

GPU cooler design is such that there is no one right answer. Because open air designs can rely on large axial fans with little air resistance, they can be very quiet. But overall cooling becomes the chassis’ job. Otherwise blowers are fully exhausting and work in practically any chassis – no matter how bad the chassis cooling is – but it is nosier thanks to the high-RPM radial fan. NVIDIA for their part has long favored blowers, but this appears to be at an end. It does make me wonder what this means for their OEM customers (whose designs often count on the video card being a blower), but that’s a deeper discussion for another time.

At any rate, from NVIDIA’s press release we know that each fan features 13 blades, and that the shroud itself is once again made out of die-cast aluminum. Also buried in the press release is information that NVIDIA is once again using a vapor chamber here to transfer heat between the GPU and the heatsink, and that it’s being called a “full length” vapor chamber, which would mean it’s notably larger than the vapor chamber in NVIDIA’s past cards. Unfortunately this is the limit to what we know right now about the cooler, and I expect there’s more to find out in the coming days and weeks. In the meantime NVIDIA has disclosed that the resulting card the standard size for a high-end NVIDIA reference card: dual slot width, 10.5-inches long.

Diving down, we also have a few tidbits about the reference PCB, including the power delivery system. NVIDIA’s press release specifically calls out a 13 phase power delivery system, which matches the low-resolution PCB render they’ve posted to their site. NVIDIA has always been somewhat frugal on VRMs – their cards have more than enough capacity for stock operation, but not much excess capacity for power-intensive overclocking – so it sounds like they are trying to meet overclockers half-way here. Though once we get to fully custom partner cards, I still expect the MSIs and ASUSes of the world to go nuts and try to outdo NVIDIA.

NVIDIA’s photos also make it clear that in order to meet that 250W+ TDP, we’re looking at an 8pin + 8pin configuration for PCIe power connectors. On paper such a setup is good for 375W, and while I don’t expect NVIDIA to go quite that far, typically we’d see a 300W 6pin + 8pin setup instead. So NVIDIA is clearly planning on drawing more power, and they’re using the connectors to match. Thankfully 8pin power connectors are fairly common on 500W+ PSUs these days, however it’s possible that older PSU owners may get pinched by the need for dual 8pin cables.

Finally, for display outputs, NVIDIA has confirmed that their latest generation flagship once again supports up to 4 displays. However there are actually 5 display outputs on the card: the traditional 3 DisplayPorts and a sole HDMI port, but now there’s also a singular USB Type-C port, offering VirtualLink support for VR headsets. As a result, users can pick any 4 of the 5 ports, with the Type-C port serving as a DisplayPort when not hooked up to a VR headset. Though this does mean that the final DisplayPort has been somewhat oddly shoved into the second row, in order to make room for the USB Type-C port.

Wrapping up the GeForce RTX 2080 Ti, NVIDIA’s new flagship has been priced to match. In fact it is seeing the greatest price hike of them all. Stock cards will start at $999, $300 above the GTX 1080 Ti. Meanwhile NVIDIA’s own Founders Edition card carries a $200 premium on top of that, retailing for $1199, the same price as the last-generation Titan Xp. The Ti/Titan dichotomy has always been a bit odd in recent years, so it would seem that NVIDIA has simply replaced the Titan with the Ti, and priced it to match.

Announcing The GeForce RTX 20 Series Previewing RTX 2080, RTX 2070, & Pre-Orders


View All Comments

  • Yojimbo - Tuesday, August 21, 2018 - link

    RT cores are practically ASIC SIPs. How is that a jack of all trades, master of none? It's targeted specifically at rendering graphics, so it is actually the opposite.

    And how does a company get profits by increasing both the cost to produce and the market price of their products? That makes no sense to me economically. Regardless of the "adequacy" of the competition, they will sell more at a lower price and have better margins with goods that are cheaper to produce. Only in special situations would a company be able to shoehorn in something that customers don't really want and get larger margins for it. That isn't the situation here with NVIDIA. They are instituting a technology transition, dedicating significant die area to a new technology, not to a useless technology. And, according to their most recent financial conference call, they expect gross margins to be down the next quarter, not up, despite the higher MSRPs of these new parts. So they don't seem to be trying to squeeze any more out of consumers, these are just more expensive parts to produce.
  • Yojimbo - Tuesday, August 21, 2018 - link

    As far as the Tensor Cores, once they are developed for the compute market, I don't think they add much to the manufacturing cost of a gaming-oriented GPU.Plus, they are vital to the viability of the ray tracing methods. Without them, real-time ray tracing would still be several years out. Reply
  • SirPerro - Tuesday, August 21, 2018 - link

    I hope you are aware that, with your logic, the third best consumer card from nvidia in 2025 would be around 1500 dollars.

    We must expect next generation products to have better performance per dollar. Otherwise we just increase price at the same rate as performance does. Yeah... it's that obvious.
  • mkaibear - Tuesday, August 21, 2018 - link

    Actually, if you assume that each generation the SKU model number goes up, so each model's "successor" is the one from the grade "below" it, you see fairly constant pricing and a constant upward scale in performance.

    Compare 780 to 970 to 1060, for example, or 780Ti to 980 to 1070.
  • eddman - Tuesday, August 21, 2018 - link

    No. Reply
  • elzafir - Tuesday, August 21, 2018 - link

    Yes. Reply
  • evernessince - Friday, August 24, 2018 - link

    The 970 is 6% faster than the 780. The 1060 3GB is 5% faster than the 970. In what world is that a "constant upward scale in performance"? I think you've drunken far too much of the Intel Kool-aid if 5-6% performance gains are considered good. Reply
  • evernessince - Friday, August 24, 2018 - link

    Following that logic we'll be at 10K consumer GPUs in no time. Nvidia will release 7nm turing and oh look the 3070 performs just as well as the 2080 so according to you that's good enough to charge insane prices. Oh and the 4070 will perform just as good as the 3080 so yay, another price hike! I hope you see the pattern by now.

    Eventually Nvidia will be forced to stop, simply because they've fleeced every penny from PC gamers. Oh well, I'm sure they'll just throw some money at the devs and their GimpWorks program and tighten their grip on AIBs to ensure no competitor can challenge them.
  • Xorp - Monday, August 20, 2018 - link

    For you. Reply
  • DanNeely - Monday, August 20, 2018 - link

    Looking at listings on Newegg, it looks like all the initial cards are using the same set of outputs as the founder edition, and presumably are a reference layout. I wonder if custom boards will add back DVI again, or if this will be the end of the road for old 2560x1600 and 1440p Korean monitors that only support DVI in. ($80-100 for a flaky adapter is a really bad deal, the cheaper ones won't work unless the monitor does something non-standard and rarely done). Reply

Log in

Don't have an account? Sign up now