On Screen Display

Before we dive into the actual display performance numbers, it makes sense to talk about NEC's OSD and a little bit about the in-monitor calibration option that's offered. 

Tapping the menu button brings up the OSD, but also enables some on-screen button labels that change accordingly as you move around inside. Rotate into portrait, and obviously buttons change - so too do the on-screen labels, which is awesome.

There are actually two sets of OSDs on the PA301w. The first is what you get when you hit menu, and is a nice (yet still comprehensive) skinned menu with pretty straightforward navigation. Settings for brightness, black, and eco mode are on the first tab, position and scaling are on the second, then color, tools, menu options, more eco settings, and finally the info tab. The second is the Advanced OSD I'll show in a moment.

What's awesome about the settings is that everything has units where possible - brightness can be changed from 40 to 400 nits, black levels can also be artificially increased to match an adjacent display. As I'll show in a second, after you've run the in-monitor calibration, if you select a specific number, it'll actually drive the display relatively close to where it should be. What a breath of fresh air compared to completely arbitrary percentages. 

Aspect ratio scaling options include full, aspect-correct, off (1:1), and custom, which is controlled from the advanced OSD. Inside the "RGB" tab are some basic color settings such as white point and simple color controls. Tools has PIP control if you want to use it, the USB port per video input mapping controls, some selection criteria for choosing video inputs, and off timer plus signaling. Menu tools is just OSD settings like position, color, and language. 

Inside "ECO" is some interesting stuff. Based on the configured price per kilowatt-hour, you can see the total electrical cost of using the monitor. In addition, based on the configured kg (of carbon) per kilowatt-hour, you can see how much carbon you've released indirectly. One field is for how much would've been used if you didn't have eco settings turned on, the other is how much you actually used. Both essentially enable some dynamic brightness based on ambient lighting measured on the front sensor - mode 1 corresponds to 200 nits of range, mode 2 corresponds to 100 nits. 

What about that "advanced OSD?" Well, you can get to it two ways. Under the color tab, at the bottom, is a link named "Advanced Settings." Pressing select on that will bring you there, or you can get there by turning on the monitor by holding power and input at the same time. Doing so then makes the menu button consistently bring up the advanced OSD for the duration of the power-on session. 

Inside are essentially the same options as the basic OSD, with more depth in the color/picture section and a few other places. White point and color tristimulus values are given in x and y, there's gamma control, and a new uniformity pane. If you're serious about getting color right, these are seriously useful. Initially however, things aren't that close to reality. Even though the white point is set at 6500K, we can see that measured value out of box is around 5600K. The color tristimulus points are also similarly completely wrong. 

This is where the in-monitor calibration is super handy, as it internally calibrates the monitor so these settings actually reflect reality instead of remain shifted by however much the monitor has drifted or differs from ideal. Initially, I spent lots of time tweaking the display color points in HCFR, shifting appropriately based on how much the numbers differed from measured. While that actually did yield better results, running the built-in calibration routine got me 90% of the way there in 1 minute instead of 1 hour like I'm used to doing manually. 

Internal calibration mode only works with x-rite i1D2 colorimeters. NEC has a rebranded version they sell in a bundle, or you can buy your own. Chances are if you're willing to spend $2k+ on an LCD, you're also willing to spend the $200 to get an i1D2. Again, it plugs into the right-side USB port. To get into calibration mode, either find stand-alone calibration in tab B of the menu, or press the left and right keys at the same time from the no signal screen. The display will initialize the sensor, then tell you to wait 30 minutes for the CCFL to settle - welcome to how long calibrating CCFL backlit displays usually takes in-between adjustments. 

After that, you can select "self" for self calibration, or "copy" mode to actually match another PA301w or another display entirely. The display will prompt you to stick the colorimeter in the center, then run through its tests. The actual set of tests seems very basic - red, green, blue, then a whitepoint and brightness test. It takes almost exactly one minute to run, then tells you it's all done. 

The results are awesome. After running through, the white point is much closer to the actual reported value, and the primary color tristimulus values are much closer to what they should be. Note below how the brightness value and color temperature value are now much closer than they were pre-calibration. 

The even better part is that the presets also now correctly work for mapping to different color spaces. If you try to use them without calibration, you risk being offset depending on how the monitor has drifted. I still ended up tweaking all six of the x y values for red green and blue, but they were much, much closer than before. 

Introduction and Hardware Impressions Viewing Angles and Color Quality
POST A COMMENT

92 Comments

View All Comments

  • Lazlo Panaflex - Tuesday, March 1, 2011 - link

    "It's seriously the Ron Jeremy of monitors if there were such a thing."

    Nah, more like John Holmes....

    2 x this beast + AMD 6990 + Crysis2 = boner-rific
    Reply
  • MeanBruce - Tuesday, March 1, 2011 - link

    Done with the slow funk, so done with Dell out the f'in door end of the driveway pickup! Welcome those beautiful 30inches! ;) Reply
  • softdrinkviking - Tuesday, March 1, 2011 - link

    Ryan,
    In there documentation, NEC claims that their calibrator is factory-tailored to NECs monitors, which seems to suggest that it is more than a "rebranding."

    Of course, this could all just be marketing, and they could be the same thing.
    Do you know for sure one way or the other?
    Reply
  • softdrinkviking - Tuesday, March 1, 2011 - link

    Oops. Brian. Not Ryan! Sorry... :) Reply
  • Ryan Smith - Wednesday, March 2, 2011 - link

    It's okay. It happens all the time. ;-) Reply
  • Brian Klug - Tuesday, March 1, 2011 - link

    From what I've seen, it really does look like a rebranded X-Rite i1D2. It's possible they've done some internal calibration as well (I know a few vendors do things like calibrate the colorimeter). It'd also make sense it's just rebranded since the i1D2 is the only thing that will work with internal monitor calibration.

    -Brian
    Reply
  • eaw999 - Wednesday, March 2, 2011 - link

    it's an i1d2 puck, but modified to allow proper calibration of wide gamut monitors. Reply
  • NEC_Art - Wednesday, March 2, 2011 - link

    Yes, the NEC calibrator is tuned by X-Rite to more correctly read our MultiSync PA Series wide gamut displays. It is not the same as a retail i1 Display2.

    Art Marshall
    Product Manager, NEC Display Solutions of America
    Reply
  • peegeenyc - Tuesday, March 1, 2011 - link

    can anyone find this for sale at a major discount retailer?
    It seems only NEC sell it at full price from my search results.
    Reply
  • Azethoth - Tuesday, March 1, 2011 - link

    "Apr 12, 2010 2:22 PM in response to: Zeno Bokor
    Re: Photoshop 10bit support
    Actually, the 10 bit/channel display path is working quite well in CS5 - on cards and displays that support it.

    Again, we've been working with the manufacturers for a while to get it working..."
    -Chris Cox (Photoshop lead)

    I would be surprised if its the only software that handles 30bit
    Reply

Log in

Don't have an account? Sign up now